MANITEX 26101C

Manufacturer Manitex
Model 26101C
Year 2014
Serial Number 210111
Condition New
Lift Capacity (pounds) 26 tons
Chassis 2014 Freightliner

Description

26101C

BOOM
Inverted T-cross section, 4-section telescoping type, extended and
retracted proportionally by double-acting hydraulic cylinder and
cable-crowd system. 4-section
29′ 5.25″ (9,0 m) to 101′ 5.25″ (30,9 m). Maximum main boom tip height
112′ 2″(34,2 m). 1-section, 29′ (8,8 m) jib. Maximum tip height 141′
4″ (43,1 m).

Boom Points – Three high-density nylon sheaves mounted on
heavy-duty roller bearings. Two removable pin-type rope guards.
Quick-reeve boom point on 101′ boom.

Boom Elevation – Double-acting hydraulic cylinder. Working
range from 9.5° below horizontal to 80.5° above.

Load Hook – 5-ton capacity hook with heavy-duty swivel and
weight is provided for single-line operation.

HOIST
Maximum theoretical line speed 247 fpm (75,3 mpm). Maximum theoretical bottom-layer line pull 12,000 lbs (5 443 kg). Two-speed planetary reducer. Spring-applied, pressure-released internal brake. Wet multi-disc internal brake is spring-applied, pressure-released.

Wire Rope – 300 feet (91,4 m) of 9/16″ (14,3 mm) diameter 6 x 25 EIPS IWRC.

SWING SYSTEM
Externally mounted, double-reduction planetary driven by hydraulic motor. Maximum theoretical swing speed 1.5 rpm. Wet multi-disc internal brake is spring applied, pressure released. Oversized diameter ball bearing swing circle with external gear. 372° non-continuous rotation.

OUTRIGGERS
21′ 6″ (6,6 m) Extended A-frame link type. Operated independently for precise leveling. Equipped with double-acting
hydraulic cylinders.

MOUNTING
Pedestal and subframe are mounted to chassis by threaded rods and clamp plates. No welding, drilling or bolting to truck frame is required.

A-Frame Stabilizers – 8′ (2,4 m) retracted; 10′ (3,1 m) extended. Operated independently for precise leveling. Double-acting hydraulic cylinders. Fixed pad size is 8″ (203,2 mm) x 11.375″ (288,9 mm).

Subframe – Torsionally resistant, rigid 4-plate design, mounted under crane full length of truck frame.

Rear Underride Protection – Supplied on factory-mounted cranes. Fabricated structure mounted under rear of bed. Complies with Bureau Motor Carrier Safety Standard 393.86.

Boom Rest – Heavy-duty, fabrication. Easily removed to simplify loading and unloading truck deck.

CONTROL SYSTEM
Dual operator platforms are equipped with four single-lever crane controls arranged to ANSI B30.5 standards. Fully proportional control valves and system pressure gauge. Each station also includes outrigger and stabilizer controls, engine start/stop, foot throttle, signal horn, boom-angle indicator, bubble levels, load charts, range diagram and audio and/or visual indicators to warn operator of overload condition.

HYDRAULICS
Hydraulic System – A 3-section vane pump direct-mounted to power take-off on truck transmissions provides 35 gpm (133 lpm) to the hoist, 8 gpm (30 lpm) to the swing circuit and 18 gpm (68 lpm) to the remaining crane functions. A 70-gallon (265-liter) baffled reservoir includes a 25-micron return line filter and magnetic plug. A single gate valve on the suction line from the tank to pump. Extensive use of SAE O-ring face seal hydraulic fittings where possible.

Hydraulic Cylinders – All load-holding cylinders are equipped with integral holding valves.

WARNING SYSTEMS
Load Moment Indicator – Senses boom hoist cylinder pressure, boom length and boom angle. Audio-visual warning indicates overload conditions and overload shutoff feature prevents continuing overload. Operator can access all relative crane configuration and load conditions via display at the operator station.

Anti-Two-Block System – Audible warning and shutoff functions prevent hook from contacting boom point.

Back-Up Alarm – Supplied on factory-mounted cranes, electronic audible motion alarm activated when truck transmission is in reverse gear.

GENERAL
Electrical – State-of-the-art, weather-resistant components throughout. Automotive style electrical system for easy installation. Designed to withstand high pressure washing and varying climates.

Design/Welding – Design conforms to ANSI B30.5. Welding conforms to AWS D1.1. Tested to SAE 1063 and SAE 765.

Manuals – Operator, service and parts manuals depict correct crane operation, maintenance procedures and parts listing.

Warranty – 12-month warranty covers parts and labor resulting from defects in material and workmanship.

Note: In order to ensure continuous improvement, specifications may change without notice.

 

FEATURES

Features

  • 26 ton (23 mton)capacity

  • 4-section,101′(30,8 m)
    proportional boom

  • 112’2″(34,2 m)maximum main boom
    tip height

  • 141’4″(43,1 m)maximum tip height

  • 1-section jib

  • 2-speed planetary hoist with
    grooved drum and negative draft flange

  • Load moment indicator with digital
    display and overload shutdown Removable boom rest

  • 21’6″(6,6 m)A-frame outriggers

  • System pressure gauge

  • Rugged,weatherproof,automotive
    style electrical system

  • Manitex UPTime Comprehensive
    Support

 

Powered by Top Rated Local®